|
How to Do Low-Cost Mold Sample Collection and Mold Laboratory Identification of Mold Species
2005 Phillip Fry
VANCOUVER, CANADA. Although any mold in elevated levels indoors
can cause severe health problems for mold-sensitive occupants,
several toxic molds such as Stachybotrys, Aspergillus, and
Penicillium pose far greater health risks than others, according
to Phillip Fry, Certified Mold Inspector and author of the book
"Mold Health Guide."
Thus, many homeowners, rental property owners, tenants,
employers, and employees in Canada, the USA, and worldwide want
to know, and need to know, the precise identities of the various
mold species infesting their moldy home, apartment, or workplace.
The accurate identification of mold species requires two steps:
(1) physical collection of mold samples from the moldy building;
and (2) mold laboratory analysis of the collected mold samples.
For the first step, a property owner, manager, tenant, or
employee usually hires a certified mold inspector, an industrial
hygienist, or an environmental hygienist for mold inspection and
collection of mold testing samples, at a typical cost of US $500
to $2,000 for a 2,000 square foot (186 square meters) home.
This inspection and testing fee usually includes mold laboratory
analysis and mold species identification for a small number
(3 to 10) of collected mold samples.
Alternatively, if the available funds for mold testing and mold
lab analysis are low, it is possible to achieve the same accurate
mold testing results for just $60 to $200 by using---
(1) inexpensive, transparent, sticky, adhesive tape (“lift tape
sampling”), such as Scotch® brand tape, to collect the mold
samples; and
(2) a low-cost Asian mold analysis laboratory (e.g., $20 per
sample for mold species identification and quantification,
compared to the usual $50 to $150 per sample in North America
or Europe).
Lift tape sampling and testing is an easy, practically-free
(except for the cost of the tape), and an effective way to
collect mold test samples when you---
(1) Can see mold growing on a wall, ceiling, floor, carpeting,
furniture, heating/cooling duct register, or other surface;
(2) Want to know whether a particular stain, discoloration, or
mystery substance on the wall or another surface is actually
mold growth; and/or
(3) Smell mold (the digestive gas emitted by mold eating the home
or building) and want to test a number of surfaces upon which
elevated levels of airborne mold spores may have landed or been
deposited, such as on walls, window sills, window and door trim,
refrigerator top, kitchen cabinet tops, undusted furniture,
heating/cooling duct registers, and the return air filter in
the heating/cooling system.
The easy steps involved in tape lift sampling are---
1. Cut a three-inch (3”) long strip of one-inch (1”) wide,
transparent sticky tape.
2. While wearing rubber gloves and a breathing respirator mask
(with organic vapor filters) from the local hardware or home
improvement store, press the tape strip firmly (sticky side down)
onto the visible mold growth or onto the surface being tested.
3. Remove (peel back) the tape from the surface.
4. Open up a small ziplock bag (a transparent, easily sealable
plastic storage bag), and press lightly the lift tape sample
sticky side onto the inside sidewall of the ziplock bag.
5. Close [zip shut] the ziplock bag completely. Tape it shut
if necessary to make sure no airborne mold spores can escape.
6. Attach to the outside of the ziplock bag a large adhesive
label with the tester’s name, date of sampling, property address,
the precise testing location at that address (e.g., “air
conditioning duct register in living room”), testing method
(“lift tape sampling”), and the name, postal address, email
address, phone number, and fax number (if any} of the person
submitting the sample to the mold laboratory.
7. Mail or express the collected lift tape samples (including
payment of the lab’s analysis fee} to the mold analysis
laboratory for mold species identification and quantification.
Contact: Phillip Fry, Manager,
Mold Inspector Laboratory International, Ltd.
Phone: 63-921-352-1287 (Vancouver, Canada)
Email: mailto:moldinspector@...
For more information about mold laboratory analysis
and mold species identification, please visit
http://www.moldlab.biz
http://www.moldinspector.com
http://www.certifiedmoldinspectors.com
http://www.moldmart.net
|
|
|
